Download on Raise3D Website: https://www.raise3d.com/pages/download

Direct link : https://s3.amazonaws.com/ideamaker/touch/updater_0_9_11_612.raisepack

 

Version 0.9.11 – June 14, 2018

  • Fixed the issue that ideaMaker does not keep the same sort order of files as the sort order in printers
  • Fixed the issue that the network is not connected automatically after reboot while using Ethernet

Version 0.9.10 – June 5, 2018

  • Added Extruder Offset Settings for N series printers
  • Added an option to choose Single or Dual version of motion board firmware update under Maintenance
  • Added more information into serial log
  • Adjusted preheating sequence to let the heated bed heating together with nozzles for Pro2 series printers
  • Added an option to disable the password to get access the remote control the touchscreen from ideaMaker when Remote Access without Password under Setting -> More Settings -> Privacy and Security disable. If you disable this option, you need set a password for remote control
  • Added an option to set the Z position of print bed dropping to after print stopped under Setting -> More Settings -> Advanced Settings
  • Added an option to set whether WLAN Password is allow to be seen or not under Setting -> More Settings -> Privacy and Security
  • Added Auto Negotiation, Port Speed, Duplex Mode as advanced settings for Ethernet tuning under Ethernet setting page. They will be available when Enable Advanced Settings enabled
  • Added temperature check for CPU of screen logic board under Maintenance
  • Fixed preheating issue after resuming a print. Or with Cool down after a print paused enabled, the print may directly start without preheating first

Version 0.9.9 – May 16, 2018

Read more about this version

  • Added a firmware upgrade wizard in Maintenance under Other
  • Added a Reconnect Serial Port button in Maintenance under Other -> Safe Mode
  • Added Enable Extruder Offset and Extruder Offset settings under More Settings -> Hardware -> Extruders
  • Added a Turn on filament sensor option under Advanced Settings
  • Added a Cool down after a print paused setting under Advanced Settings
  • Added sorting options for files and folders inside Local storage and USB storage
  • Added auto-preloading filament before unloading (for Pro2 series printers)
  • Added Camera function for Pro2 series
  • Added Allow Remote Access without Password
  • Added German Language
  • Fixed Wi-Fi connection failure issue with non-Latin characters in Wi-Fi name
  • Fixed long-time print resume loading issue after pausing by code M2000
  • Fixed the height display issue during multi-object print
  • Saved Loading/Unloading nozzle temperature after reboot
  • Saved Move Step unit after reboot

Version 0.9.7 – January 16, 2018

Read more about this version

  • Lower Printing Temperature Available
  • User-defined Screen Lock Timeout
  • Empty Password for Screen Lock
  • SSH Password Security for Privacy and Security
  • Backup Credential File
  • Export Local Storage
  • Check Storage Space before Operation
  • User-defined Jerk
  • User-defined Acceleration
  • Save More Records for Serial Port Log
  • Fixed the bug of temperature not updating in time
  • Pause Reason Prompt

Version 0.9.2 – June 14, 2017

  • Added option to clear print statistics
  • Added option to reset privacy and security settings
  • Added option to restore factory settings
  • Added option to disable or enable collecting print statistics in dashboard
  • Added option to set steps per unit and PID settings
  • Fixed the issue that the height ratio of the printed models is incorrect when printing multiple models in sequential order

Version 0.9.0 – March 29, 2017

  • Added support for Russian language
  • Added support for Japanese language
  • Added a feature to restore last saved screen brightness
  • Added a feature to show the estimated completed time
  • Added a feature to show the initialization stage of WiFi and Ethernet
  • Added option to set the target pre-heat temperature while recovering the print job
  • Added option to clear print information after the print job is completed
  • Added option to enable screen lock
  • Cooling down the extruders after finishing loading or unloading filaments
  • Improved connecting via ethernet with a static IP address
  • Corrected gcode name and file size in dashboard

Version 0.8.0 – November 21, 2016

  • Added print time and material used in preview mode
  • Added a function to sync real time when turning on the printer
  • Added a function to record printing time and material used amount
  • Improve the uploading speed of gcode
  • Show target parameter and current parameter in Tune menu
  • Fixed a bug of not enabling DHCP when connected with LAN
  • Fixed the problem of wrong printing speed after resuming

Version 0.7.2 – August 19, 2016

  • Added a cursor in input box
  • Added a record of serial port log which can be loaded out to USB device or SD card
  • Added a prompt of the error of motion board
  • Added a Z drop when print finish in order to remove the model easily
  • Fixed some problems of UI display
  • Fixed a bug of keyboard letter
  • Fixed a bug of recognizing notes when reading gcode

Version 0.7.0 – June 15, 2016

  • Added a feature to pre-extrude manually while retracting filaments
  • Added “FastStop” function to stop printing while pre-heating extruders and heat bed
  • Added update notifier
  • Added a feature to set SSH password
  • Added French language support
  • Added support for setting up custom WiFi
  • Added a function of system monitoring to shut down touchscreen under crash situation
  • Improved virtual keyboard for extended symbols
  • Added a function to check uploaded file information and print uploaded file in upload queue
  • Improved WiFi connection

Version 0.6.7 – April 27, 2016

  • Added a feature to display current layer number and printed height in ‘Home’ page
  • Added a feature to adjust the flow rate for left/right nozzle separately in ‘Tune’ page
  • Added a feature to show motion controller board firmware version in ‘Setting’ page
  • Added a feature to show the full name of the firmware when selected
  • Fixed a bug of printing with wrong nozzle after pausing to swap filament

Version 0.6.5 – March 29, 2016

  • Added printing task recovery list (support recovering interrupted printing task due to motion controller board error, file error and power loss)
  • Added a function to create folders in local storage
  • Added a function to copy, move, delete and rename multiple files and folders
  • Added a safe mode for printer, supporting all operations except printing and controlling XYZ axis and extruders
  • Added a battery volume display
  • Added WiFi signal strength display
  • Added a setting for time and time zone
  • Added a function to set temperature in the “Home” page
  • Added a function to restore default flow rate after finishing print
  • Improved system stability
  • Added a function to refresh the model list after finishing uploading
  • Fixed a bug to delete .data file with .gcode file together
  • Fixed a bug when resuming from pause

Version 0.6.1 – January 31, 2016

  • Add electrical board error information reminder
  • Fix a loading bug when resuming or re-print a job
  • When changing settings under ‘Tune’ menu, there is no need to delete the existing number before inputting new number and the existing number is highlighted
  • Add a print cache file to help resuming or re-print a job

Version 0.5.8 – January 13, 2016

  • Force cooling all of nozzles while printing is stopped or finished
  • Improve moving step of nozzle while calibrating bed level
  • Improve touch experience
  • Add popup message with sensor issues
  • Fix issues on UI interface

Version 0.5.7 – January 8, 2016

  • Improve error handling for file cache
  • Hide empty USB drive
  • Fix encoding issue while transferring list of file names
  • Fix issue that files view is invalid while USB or SD card has been plugged out

Version 0.5.6 – January 6, 2016

  • Added file cache while print files from SD card or USB
  • Added file remove functionality
  • Added battery voltage view in Setting-Other tab
  • Added tip for saving dump file on the screen while power loss is occurred
  • Fix encoding issue while parsing print template
  • Fix issue that file info is incomplete in the uploading queue
  • Improved UI layout
Facebook Comments